Pressure Canning Step By Step

These general directions for using your pressure canner may serve as a guide and a reminder to the basic steps in home pressure canning food, but you should refer to the more specific directions that came with your pressure canner.


    1. The first step in pressure canning is to clean, inspect and assemble the pressure canner. Before each canning season, check the dial gauge for accuracy. The dial gauge is a delicate instrument which must be handled with care. Do not submerse cover or let gauge come in contact with any liquid. You should have the gauge inspected if the cover has been submerged in water or dropped, gauge glass is broken or has fallen out, parts are rusty, pointer is not in the “0” block, or if you believe the gauge may not be accurate. The gauge can usually be checked at your local county extension office. If you are unable to have your dial gauge checked locally, carefully remove the gauge and call your canner’s Consumer Service Department for directions. Also check the sealing ring, overpressure plug, and the rubber gasket of the air vent/cover lock. Replace these parts when they become hard, deformed, cracked, worn, pitted, or unusually soft. Wash 8 (1 quart ) canning jars, bands, and lids in hot soapy water and rinse. Dry bands and set aside. Place the jars and lids in 180-degree (near-boiling) water for at least 10 minutes. Also sterilize the tongs you use to put them in the boiling water and take them back out. Don’t touch them with your hands after you sterilize them. Keep the jars and lids hot until used.
    2. Check the jars for nicks, cracks, and sharp edges. Check the rings (screw bands) for dents or rust. Use only jars, lids, and bands in perfect condition so an airtight seal may be obtained. Wash and rinse jars, lids, and bands. Pour hot water into jars and set aside until needed. The jars and lids don’t need to be sterile, just clean and warm (to prevent breakage from thermal shock). The canner will sanitize both the contents and the jars!
    3. Put the canner on your stove, centering on the burner. If you have a glass or ceramic stove, be sure that the canner does not overextend the burner by more than 1 inch, and check the stove’s manual to be sure the use of a pressure canner is ok.
    4. The amount of water to put in the canner depends upon the canner, so always refer to the directions that came with your canner. The 23 quart Presto directions call for “3 quarts of boiling water, canning rack, and jars in canner. To prevent water stains on jars, add 2 tablespoons white vinegar to water in canner. Always use the canning rack that came with the canner. Jars may break if set directly on bottom of canner. In general, 3 inches of hot water into the canner. Too much water is unlikely to cause harm, but too little could boil dry and that would be a major problem. To prevent water stains on jars, add 2 tablespoons white vinegar to water in canner. Always use canning rack. Jars may break if set directly on bottom of canner.
    5. Start the canner heating up by turning the burner on to a low setting to warm the water. Take care not to set it too high and boil off the water or reduce the level, while you are filling the jars.


    1. Select fresh firm food.
    2. Sort food according to size.
    3. Clean food thoroughly.
    4. Prepare according to recipe.
    5. Fill hot canning jars promptly with food and liquid to recommended level. Allow ½-inch headspace for fruits. ALL vegetables and meats require 1-inch headspace due to expansion during processing.
    6. Work out air bubbles with a clean nonmetallic spatula.
    7. Wipe sealing edge clean with a damp cloth.
    8. Adjust bands according to closure manufacturer’s directions.
    9. Look through the vent pipe to be certain it is open before placing cover on canner. To clean the vent pipe, draw a pipe cleaner or small brush through the opening.


    1. Vent (exhaust) air from the canner and jars by adjusting the burner’s heat to a relatively high setting to create a steady flow of steam from the vent pipe. Consult the instruction book which accompanied your range for recommended heat setting. Reduce heat to maintain a moderate steam flow. Allow steam to flow for 10 minutes to fill the canner with steam and remove air.


    1. Place the pressure regulator [the regulator weight] on the vent pipe. Set the burner at a relatively high heat setting, on most range burners, and heat the canner until the pressure dial gauge registers desired pressure.
    2. The processing time begins when pressure gauge reaches the correct pressure. Adjust heat to maintain correct pressure on the dial gauge. That may take a few tweaks! For canners without dial gauges, start timing when the weighted gauge begins to jiggle or rock. One type of weighted gauge should jiggle 2 or 3 times per minute, while another type should rock slowly throughout the process – check the manufacturer’s directions.
    3. NOTES: Loss of pressure at any time can result in under processing, or unsafe food. Quick and large pressure variations during processing may cause unnecessary liquid losses from jars.


  1. At end of processing time, turn burner to “OFF” and remove canner from heat source. Lift pressure canner to remove it from burner. Sliding cookware can leave scratches on stovetops.
  2. Let pressure drop of its own accord, do not quick-cool. Do not run water over the canner! Pressure is completely reduced when the air vent/cover lock and overpressure plug have dropped and no steam escapes when the pressure regulator is tilted. Do not use the pressure dial gauge as an indicator for when pressure is completely reduced. Attempting to speed the cooling of the canner may cause jar breakage. Standard size heavy-walled canners require about 30 minutes when loaded with pints and 45 minutes when loaded with quarts. Newer thin-walled canners, like the Presto models, cool more rapidly and are equipped with vent locks that are designed to open when the pressure is gone. These canners are depressurized when the piston in the vent lock drops to a normal position. Often you can hear a click when it drops.
  3. When the pressure has been completely reduced, remove pressure regulator from vent pipe and let canner cool for 10 minutes. Do not remove the pressure regulator until pressure is completely reduced and the air vent/cover lock has dropped. Always remove pressure regulator before opening the cover.
  4. Open the canner. Note: take care when opening a hot canner! Lift the canner cover toward you to keep steam away from you when opening. If cover seems to stick or is hard to turn, do not force it open. Sticking may indicate that there is still pressure inside the canner. If in doubt about pressure being completely reduced, let the canner stand until cool before removing the cover.
  5. Remove jars from canner with a jar lifter, trying to keep them upright without tilting. Set jars apart on board or cloth away from draft to cool. A towel or cake cooling rack makes a good surface. Leave at least one inch of space between the jars during cooling. Let the jars sit undisturbed while they cool, normally 8 to 12 hours. Do not tighten the ring bands on the lids or push down on the center of the flat metal lid while the jars are cooling.
  6. Once the jars are cooled, remove ring bands from sealed jars (otherwise the bands may rust in place and be hard to open). If necessary, wash jars and lids to remove all residues Put any unsealed jars in the refrigerator and use those first.
  7. Test Jar SealsWhen jars are cold, test seal, remove bands, wipe jars, label, date, and store in a cool, dry place. Most canner foods will taste good for about a year. Technically, they are safe for years past this, as long as they remained sealed, stored properly and show no signs of spoilage. But after a year or two the quality and taste will appreciably decline.

Prepare Your Family for Emergencies

Signup Now to Get Our Exclusive Newsletter with DIY tips, guides, and quizzes!!